Enhancing the Thermal Efficiency of Longitudinally Finned Parabolic Trough Solar Receivers
DOI:
https://doi.org/10.52825/solarpaces.v3i.2281Keywords:
Parabolic Trough Receiver, Longitudinal Fins, Non-Uniform Heat Flux, Conjugate Heat TransferAbstract
The objective of this study was to investigate the conjugate heat transfer in a longitudinally finned parabolic trough solar thermal receiver tube, taking into account the non-uniform heat flux distribution along the tube circumference. Both smooth and longitudinally finned stainless steel receiver tubes, with Syltherm 800 oil as the heat transfer fluid, were numerically simulated using Ansys Fluent 2023R2 with periodic boundary conditions for Reynolds numbers ranging from 20,000 to 60,000. Two fin configurations were investigated in the study: two fins - of little practical interest but very useful to gain physical insight into the problem - and six fin receiver tubes. In addition, sub-cases within the two- and six-fin configurations were analyzed by varying the position and height of the fins. It was found that fins on the bottom side, exposed to a higher heat flux, mainly enhanced conduction, while fins on the top side mainly enhanced convection by directing higher velocity values toward the bottom side. To reduce hot spots and improve thermal efficiency, fins should be located in higher heat flux areas, and shorter fins on the bottom side and longer fins on the top side are recommended. Finally, the performance evaluation criteria were assessed using both the inner Nusselt number, based on the convective heat transfer coefficient as commonly reported in the literature, and an overall Nusselt number, based on the total heat transfer resistance of the receiver. For the most favorable two-fin and six-fin cases, the maximum temperature in the receiver decreased by a maximum of 16.7 K and 30 K, respectively.
Downloads
References
[1] H. Price, E. Lüpfert, D. Kearney, E. Zarza, G. Cohen, R. Gee, and R. Mahoney, “Ad-vances in Parabolic Trough Solar Power Technology,” J. Sol. Energy Eng., vol. 124, no. 2, pp. 109–125, May 2002, doi: 10.1115/1.1467922.
[2] H. Price, M. J. Hale, R. Mahoney, C. Gummo, R. Fimbres, R. Cipriani, “Developments in High Temperature Parabolic Trough Receiver Technology,” Proc. ISEC, vol. 2004, pp. 659–667, Dec. 2004, doi: 10.1115/ISEC2004-65178.
[3] H. Price, R. Forristall, T. Wendelin, A. Lewandowski, T. Moss, C. Gummo, “Field Survey of Parabolic Trough Receiver Thermal Performance,” Proc. ISEC, pp. 109-116, 2006, doi: 10.1115/ISEC2006-99167.
[4] J. Li, Z. Wang, D. Lei, J. Li, “Hydrogen permeation model of parabolic trough receiver tube,” Sol. Energy, vol. 86, no. 5, pp. 1187-1196, May 2012, doi: 10.1016/j.solener.2012.01.011.
[5] L. Moens, D. M. Blake, “Mechanism of Hydrogen Formation in Solar Parabolic Trough Receivers,” NREL Report, no. 42881, pp. 1–10, 2008.
[6] E. Bellos, C. Tzivanidis, and D. Tsimpoukis, “Thermal enhancement of parabolic trough collector with internally finned absorbers,” Sol. Energy, vol. 157, pp. 514–531, Aug. 2017, doi: 10.1016/j.solener.2017.08.067.
[7] Sh. Ghadirijafarbeigloo, A.H. Zamzamian, M. Yaghoubi, “3-D Numerical Simulation of Heat Transfer and Turbulent Flow in a Receiver Tube of Solar Parabolic Trough Concen-trator with Louvered Twisted-tape Inserts,” Energy Procedia, vol. 49, pp. 373-380, 2014, doi: 10.1016/j.egypro.2014.03.040.
[8] İ. H. Yılmaz, A. Mwesigye, T. T. Göksu, “Enhancing the overall thermal performance of a large aperture parabolic trough solar collector using wire coil inserts,” Sustain. Energy Technol. Assess., vol. 39, 2020, doi: 10.1016/j.seta.2020.100696.
[9] K. A. Ahmed, E. Natarajan, “Thermal performance enhancement in a parabolic trough receiver tube with internal toroidal rings: A numerical investigation,” Appl. Therm. Eng., vol. 162, 2019, 114224, doi: 10.1016/j.applthermaleng.2019.114224.
[10] P. Wang, D.Y. Liu, C. Xu, “Numerical study of heat transfer enhancement in the receiver tube of direct steam generation with parabolic trough by inserting metal foams,” Appl. Energy, vol. 102, pp. 449-460, 2013, doi: 10.1016/j.apenergy.2012.07.026.
[11] M. Allam, M. Tawfik, M. Bekheit, E. El-Negiry, “Heat transfer enhancement in parabolic trough receivers using inserts: A review,” Sustain. Energy Technol. Assess., vol. 48, 2021, 101671, doi: 10.1016/j.seta.2021.101671.
[12] E. Bellos, C. Tzivanidis, D. Tsimpoukis, “Multi-criteria evaluation of parabolic trough col-lector with internally finned absorbers,” Appl. Energy, vol. 205, pp. 540-561, 2017, doi: 10.1016/j.apenergy.2017.07.141.
[13] B. Kurşun, “Thermal performance assessment of internal longitudinal fins with sinusoidal lateral surfaces in parabolic trough receiver tubes,” Renew. Energy, vol. 140, pp. 816-827, 2019, doi: 10.1016/j.renene.2019.03.106.
[14] E. Bellos, C. Tzivanidis, “Enhancing the performance of a parabolic trough collector with combined thermal and optical techniques,” Appl. Therm. Eng., vol. 164, 2020, 114496, doi: 10.1016/j.applthermaleng.2019.114496.
[15] A. Laaraba, G. Mebarki, “Enhancing Thermal Performance of a Parabolic Trough Collec-tor with Inserting Longitudinal Fins in the Down Half of the Receiver Tube,” J. Therm. Sci., vol. 29, pp. 1309–1321, Apr. 2020, doi: https://doi.org/10.1007/s11630-020-1256-8.
[16] P. Liu, T. Ren, Y. Ge, W. Liu, L. Chen, “Performance analyses of a novel finned parabol-ic trough receiver with inner tube for solar cascade heat collection,” Sci. China Technol. Sci., vol. 66, pp. 1417–1434, 2023, doi: 10.1007/s11431-022-2201-3.
[17] E. Bellos, C. Tzivanidis, D. Tsimpoukis, “Optimum number of internal fins in parabolic trough collectors,” Appl. Therm. Eng., vol. 137, pp. 669-677, 2018, doi: 10.1016/j.applthermaleng.2018.04.037.
[18] V. Kumar, S. Savino, C. Nonino, “Effect of height and position of inner rectangular longi-tudinal fins in parabolic trough solar receivers,“ Comput. Therm. Sci.: An Int. J., vol. 17 (3), pp. 1–11, 2025, doi: 10.1615/ComputThermalScien.2024055167.
[19] A. Fernández-García, E. Zarza, L. Valenzuela, M. Pérez, “Parabolic-trough solar collec-tors and their applications,” Renew. Sustain. Energy Rev., vol. 14, no. 7, pp. 1695-1721, Jul. 2010, doi: 10.1016/j.rser.2010.03.012.
[20] ANSYS, Inc. 2023 Ansys Fluent Theory Guide, release 2023R2.
[21] R.L. Webb and E.R.G. Eckert, “Application of rough surfaces to heat exchanger design,” Int. J. Heat Mass Transf., vol. 15, no. 9, pp. 1647–1658, Sep. 1972, doi: 10.1016/0017-9310(72)90095-6.
[22] Gnielinski V. New equations for heat and mass transfer in turbulent pipe and channel flow. Int Chem Eng 1976; 16:359–68.
[23] Blasius H. Das Aehnlichkeitsgesetz bei Reibungsvorgängen in Flüssigkeiten, Mitteilungen über Forschungsarbeiten auf dem Gebiete des Ingenieurwesens, 131; 1913.
Published
How to Cite
Conference Proceedings Volume
Section
License
Copyright (c) 2025 Vinod Kumar, Stefano Savino, Carlo Nonino
This work is licensed under a Creative Commons Attribution 4.0 International License.
Accepted 2025-10-06
Published 2025-11-28